收藏本站
ISL29011
FIGURE 1. I 2 C TIMING DIAGRAM
Principles of Operation
Photodiodes and ADC
The ISL29011 contains two photodiode arrays which convert
light into current. The spectral response for ambient light sensing
and IR sensing is shown in Figure 8 in the performance curves
section. After light is converted to current during the light signal
process, the current output is converted to digital by a built-in
16-bit Analog-to-Digital Converter (ADC). An I 2 C command reads
the ambient light or IR intensity in counts.
The converter is a charge-balancing integrating type 16-bit ADC.
The chosen method for conversion is best for converting small
current signals in the presence of an AC periodic noise. A 100ms
integration time, for instance, highly rejects 50Hz and 60Hz power
line noise simultaneously. See “Integration and Conversion Time”
on page 12.
The built-in ADC offers user flexibility in integration time or
conversion time. Integration time is determined by an internal
oscillator (f OSC ), and the n-bit (n = 4, 8, 12,16) counter inside the
ADC. A good balancing act of integration time and resolution
depending on the application is required for optimal results.
The ADC has I 2 C programmable range select to dynamically
accommodate various lighting conditions. For very dim conditions,
the ADC can be configured at its lowest range (Range 1) in the
ambient light sensing. For very bright conditions, the ADC can be
configured at its highest range (Range 4) in the proximity sensing.
Low-Power Operation
The ISL29011 initial operation is at the power-down mode after a
supply voltage is provided. The data registers contain the default
value of 0. When the ISL29011 receives an I 2 C command to do a
one-time measurement from an I 2 C master, it will start ADC
conversion with light or proximity sensing. It will go to the
7
power-down mode automatically after one conversion is finished
and keep the conversion data available for the master to fetch
anytime afterwards. The ISL29011 will continuously do ADC
conversion with light or proximity sensing if it receives an I 2 C
command of continuous measurement. It will continuously
update the data registers with the latest conversion data. It will
go to the power-down mode after it receives the I 2 C command of
power-down.
Ambient Light, IR and Proximity Sensing
There are six operational modes in ISL29011: Programmable ALS
once with auto power-down, programmable IR sensing once with
auto power-down, programmable proximity sensing once with auto
power-down, programmable continuous ALS sensing,
programmable continuous IR sensing and programmable
continuous proximity sensing. These six modes can be
programmed in series to fulfill the application needs. The detailed
program configuration is listed in “Register Set” on page 10.
When the part is programmed for ambient light sensing, the
ambient light with wavelength within the “Ambient Light
Sensing” spectral response curve in Figure 8 is converted into
current. With ADC, the current is converted to an unsigned n-bit
(up to 16 bits) digital output.
When the part is programmed for infrared (IR) sensing, the IR
light with wavelength within the “IR or Proximity Sensing”
spectral response curve on Figure 8 is converted into current.
With ADC, the current is converted to an unsigned n-bit (up to 16
bits) digital output.
When the part is programmed for proximity sensing, the external
IR LED is turned on by the built-in IR LED driver through the IRDR
pin. The amplitude of the IR LED current and the IR LED
modulation frequency can be programmed through Command
Register II. When the IR from the LED reaches an object and gets
reflected back, the reflected IR light with wavelength within the “IR
FN6467.5
October 10, 2012
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
ISL29012IROZ-EVALZ EVALUATION BOARD ISL29012IROZ
ISL29013IROZ-EVALZ EVALUATION BOARD FOR ISL29013
ISL29015IROZ-EVALZ EVALUATION BOARD FOR ISL29015
ISL29018IROZ-EVALZ EVALUATION BOARD FOR ISL29018
ISL29020IROZ-EVALZ EVALUATION BOARD FOR ISL29020
ISL29021IROZ-EVALZ EVAL BOARD FOR ISL29021IROZ
ISL29023IROZ-EVALZ EVALUATION BOARD ISL29023IROZ
ISL29028AIROZ-EVALZ BOARD EVALUATION FOR ISL29028
相关代理商/技术参数
ISL29011IROZ-T7 功能描述:IC PROXIMITY SENSOR AMB LT 8ODFN RoHS:是 类别:传感器，转换器 >> 多功能 系列:- 其它有关文件:Automotive Product Guide 标准包装:2,500 系列:- 传感器类型:光线和近程 输出类型:I²C?
ISL29011IROZ-T7R5484 制造商:Intersil Corporation 功能描述:ISL29011IROZ-T7 DOMINANT ASSY AND UNISEM TEST ONLY - Tape and Reel 制造商:Intersil Corporation 功能描述:IC PROXIMITY SENSOR AMB LT 8ODFN 制造商:Intersil Corporation 功能描述:ISL29011IROZ-T7 DOMINANT ASSY AND CARSEM TEST ONLY T/R
ISL29012IROZ-EVALZ 功能描述:EVALUATION BOARD ISL29012IROZ RoHS:是 类别:编程器，开发系统 >> 评估板 - 传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:-
ISL29012IROZ-T7 功能描述:IC SENSOR LIGHT-DGTL I2C 6-ODFN RoHS:是 类别:传感器，转换器 >> 光学 - 光电探测器 - 环境光传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 产品变化通告:Product Discontinuation 25/Jun/2012 标准包装:2,500 系列:- 带接近传感器:无 波长:- 电源电压:1.7 V ~ 2 V 电流 - 暗（标准）:- 电流 - 光（典型值）:- 输出类型:数字 - I²C 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UDFN 裸露焊盘 包装:带卷 (TR)
ISL29013IROZ 制造商:Intersil Corporation 功能描述:Light-To-Digital Sens,ISL29013IROZ
ISL29013IROZ-EVALZ 功能描述:EVALUATION BOARD FOR ISL29013 RoHS:是 类别:编程器，开发系统 >> 评估板 - 传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:-
ISL29013IROZ-T7 功能描述:光学数位转换器 ISL29013IROZ LIGHT- TO-DIGTL OUTPUT SNSR RoHS:否 制造商:ams 数据总线宽度: 峰值波长:470 nm 最大工作频率: 工作电源电压: 工作电流: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:Chipscale-6 封装:Reel
ISL29015IROZ-EVALZ 功能描述:EVALUATION BOARD FOR ISL29015 RoHS:是 类别:编程器，开发系统 >> 评估板 - 传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:-